Evokomoribi presents A0123 as a rechargeable rabbit vibrator with separate head and ear motors. Its mint-green and purple gallery shows a curved main shaft, twin ear tips and local controls near the handle. The manufacturer describes seven patterns per motor and independent selection; for a buyer, the useful distinction is how those two zones are selected and stopped. The page supplies an overall size and mass, but its electrical sheet contains an incorrect current unit and omits charging and runtime figures.
The power table needs clarification before it becomes an accepted specification.
The following entries reproduce the supplier's scope and units. Working voltage, charging voltage, stored capacity and current are different quantities; the erroneous current entry is retained as a discrepancy, not corrected by assumption.
| Parameter | Published specification | What to confirm |
|---|---|---|
| Overall size / mass | 210 × 37 × 33 mm; 175 g [1] | Supplier exterior values, without labeled contact length, shaft diameter, ear spacing or tolerances. No net-versus-set mass definition was established. |
| Motor and pattern claim | 2 motors; 7 patterns each; independent selection and 49 combinations claimed [1] | Supplier text and buyer-confirmed labels, not a witnessed state matrix. No start/stop, mode-memory or transition sequence is published in the material reviewed. |
| Material | Food-grade silicone + ABS, supplier wording [1] | No formulation or matched contact-material report was reviewed; exterior appearance does not establish every component's composition. |
| Operating voltage / standby | 3.7 V; ≤2 µA standby current [1] | Supplier values without measurement conditions. The standby figure does not establish battery capacity or runtime. |
| Maximum operating current | Source writes 1.0Ah [1] | Ah denotes charge capacity rather than electric current. The intended current value is unresolved; do not silently convert this to 1 A or call it a 1,000 mAh cell. |
| Charging assembly | Magnetic charging stated; DC 5V and two contacts visible [1] [2] | The graphic supports the marked input and contact arrangement, not polarity, pitch, input current, cable compatibility or enclosure testing. |
| Endurance | Run and charge time not specified; cell capacity not established [1] | The page says these durations are not specified in its source XLS. QQIP did not obtain that underlying sheet and cannot fill the gaps from another model. |
| Water / sound | IPX6; ≤60 dB at 30 cm claimed [1] | No matching test report or full acoustic conditions were authenticated. The water claim is not an immersion instruction. |
| Order reference | 100-unit model MOQ; 25–35 days after approved sample and deposit stated [1] | Model FAQ reference, not a live quotation or shipment promise. Requested motor, color, artwork and packaging changes need their own written scope. |
Separate what the model text says from what its control image shows.
| Topic | Evidence | Question for this model |
|---|---|---|
| Head and ear roles | The page assigns one motor to each zone and seven patterns to each motor. | Obtain a labeled button diagram and confirm whether either zone can run alone, pause independently or be turned off without shutting down the whole device. |
| Local controls | The handle illustration has two waveform marks in an elongated outlined area and a separate power mark. | The symbols do not establish the internal switch arrangement or press timing. Match the actual supplied manual to the sample rather than inventing a sequence from the drawing. |
| 49-combination claim | The supplier expressly multiplies its two seven-pattern lists into 49 possible combinations. | Demonstrate the selection matrix and stop behavior on the offered revision. The claim is not a QQIP functional test or evidence of 49 distinct measured outputs. |
| Output comparison | Two zones are described, but no amplitude or finished-device frequency values are provided. | Compare each zone under an agreed sample configuration; pattern counts do not rank vibration strength against another rabbit model. |
Use the pictured controls to identify the offered revision.
The handle view places a power mark above an elongated area carrying two waveform marks. For sample approval, ask the supplier to label which input selects the head and which selects the ear motor. Keep that marked diagram with the agreed operating instructions; do not infer a long-press or stop sequence from the symbols alone. [3]
Original A0123 illustration with the handle controls visible. The displayed symbols help match the sample and artwork; they do not prove the mechanical switch layout or independently verify motor behavior. [3]
View the original source illustration ↗The rear DC 5V mark does not resolve the 1.0Ah current error.
Match the charging lead to the illustrated contacts
The rear and side images locate two contacts just above the purple handle section and show a DC 5V mark. This is more specific than the word rechargeable, but neither image dimensions the contact spacing or states polarity. Obtain the supplied cable identity and input-current requirement; a similar magnetic cable is not proven interchangeable. [2]
Request a corrected sheet rather than choosing a plausible number
The technical table's maximum-operating-current entry is 1.0Ah. It cannot define a motor current limit, and it should not be reinterpreted as battery capacity simply because both are electrical specifications. Ask the manufacturer to identify the intended value, unit and measurement state in a revision-controlled sheet. Runtime and full-charge timing remain separate missing entries. [1]
Keep the offered A0123 separate from general app and certification claims.
No app edition established by the anonymous testimonial
The model page contains an anonymous account of branded-app and BLE firmware work. It identifies no A0123 revision, application, supported phone system or pairing instructions. The illustrated model has local controls; this sourcing page does not add app operation from that general case. If an app edition is offered, it needs a distinct specification and demonstration. [1]
Document names are a request list, not reviewed results
The FAQ advertises declarations, material and battery documents, but the reviewed model page does not expose the underlying report files for authentication. Buyer-confirmed and verified-feedback labels are also publisher assertions without order evidence available to QQIP. Keep the quoted model, motor revision and charging arrangement attached to each requested document; do not turn those labels into an independent platform approval. [1]
Sources and editorial review
QQIP Editorial reviewed the official A0123 specifications, model FAQ and six full-size model images on 9 October 2026. Dimensions, mass, pattern combinations and order references are manufacturer statements. No physical sample was tested. The underlying electrical sheet, contact-material report and model test documents were not available for independent review.
- Evokomoribi — A0123 model specifications and FAQ ↗
Two-zone architecture, pattern/combination claims, dimensions, material, power discrepancy and model order references; anonymous cases and document claims are not independently confirmed.
- A0123 rear contact and DC 5V illustration linked by Evokomoribi ↗
Two rear contacts and DC 5V marking; no cable polarity, pitch or current rating.
- A0123 control-symbol illustration linked by Evokomoribi ↗
Power mark and two waveform marks on the pictured handle; image does not establish press timing or the internal switch arrangement.